WM5 for all

Jun 16, 2006, 10:09 AM #1
maverick808 Senior Member Join: Apr 2006 Posts: 169	USB WM5 for all Previously my colleague and I wrote a little app to let developers use WM5 devices inside Parallels. I've now improved it and now it should let all users sync their WM5 devices in Parallels. Without this app in Parallels WM5 devices may only sync one time and will always disconnect after a minute or so. This app fixes this so that WM5 devices reliably sync and will never disconnect unless you actually unplug the device. I hope at least a few of you find it useful. To use it you must first put your WM5 device in serial mode. To achieve this either use the USBSwitch app which might already be on your device in Start->Accessories or ActiveSync Mode which is in Settings->Connectons. If you have neither of the above already on your device then install and try USBSwitch from here. Next just install the app which you can download from here. Run the app and your WM5 device should sync up and work fine. Updated: Version 0.2 released (just fixes the annoying exception when shutting Windows down)

Jun 16, 2006, 10:09 AM

maverick808
Senior Member

Join: Apr 2006
Posts: 169

USB WM5 for all

Previously my colleague and I wrote a little app to let developers use WM5 devices inside Parallels. I've now improved it and now it should let all users sync their WM5 devices in Parallels. Without this app in Parallels WM5 devices may only sync one time and will always disconnect after a minute or so. This app fixes this so that WM5 devices reliably sync and will never disconnect unless you actually unplug the device. I hope at least a few of you find it useful.

To use it you must first put your WM5 device in serial mode. To achieve this either use the USBSwitch app which might already be on your device in Start->Accessories or ActiveSync Mode which is in Settings->Connectons.

If you have neither of the above already on your device then install and try USBSwitch from here.

Next just install the app which you can download from here.

Run the app and your WM5 device should sync up and work fine.

Updated: Version 0.2 released (just fixes the annoying exception when shutting Windows down)

Jun 16, 2006, 11:56 AM #2
rbushway Junior Member Join: May 2006 Posts: 8	Thank you! Thank you! Thank you! It works like a charm. For the first time since running Parallels, I'm able to sync my Treo 700W to Outlook!

Jun 16, 2006, 02:09 PM #3
Randy Junior Member Join: May 2006 Posts: 3	Fantastic! Works like a champ - just make sure you see the five little but crucial words - after you RUN THE APP - which I missed, thinking it was some kind of patch - but it's an additional app that will run in the system tray - and it works! Thanks, maverick808 & colleague.

Jun 16, 2006, 03:51 PM #4
PetraHonig Junior Member Join: May 2006 Posts: 10	Hi, can you give me a tip how to use your tools ? I have ActiveSync 4.1 in my parallels Desktop (final version). When I connect my PPC, it's recognized and XP installs it as a "Windows Mobile-based Device" but ActiveSync can not find it. Then I installed USBSWITCH on the PPC and changed ActiveSync mode to "Serial". Now the PPC is recognized as "WindowsCE.NET 5.0" device but XP can not install a driver for it. It has still a yellow marker in the Device Manager. Then I start SyncAlive and it appers in the bar but that's all. When I now start ActiveSync the behaviour is just the same as without your program and the changed settings using USBSWITCH. Am I using your tools correctly ?

Jun 16, 2006, 03:51 PM

PetraHonig
Junior Member

Join: May 2006
Posts: 10

Hi,

can you give me a tip how to use your tools ?

I have ActiveSync 4.1 in my parallels Desktop (final version). When I connect my PPC, it's recognized and XP installs it as a "Windows Mobile-based Device" but ActiveSync can not find it.

Then I installed USBSWITCH on the PPC and changed ActiveSync mode to "Serial". Now the PPC is recognized as "WindowsCE.NET 5.0" device but XP can not install a driver for it. It has still a yellow marker in the Device Manager. Then I start SyncAlive and it appers in the bar but that's all.

When I now start ActiveSync the behaviour is just the same as without your program and the changed settings using USBSWITCH.

Am I using your tools correctly ?

Jun 16, 2006, 04:08 PM #5
steltenp1 Junior Member Join: Apr 2006 Posts: 7	Absolutely Amazing Thanks! This works beautifully. It was the one thing that was making me start to question if Parallels was worth the money ... now it definitely is.

Jun 16, 2006, 04:08 PM

maverick808
Senior Member

Join: Apr 2006
Posts: 169

Quote:

Originally Posted by PetraHonig

Am I using your tools correctly ?

Did you actually run the application? Do you see the SyncAlive icon in the system tray?

__________________
WiFiFoFum Pocket PC Wardriving
www.aspecto-software.com

Jun 16, 2006, 04:14 PM

PetraHonig
Junior Member

Join: May 2006
Posts: 10

Quote:

Originally Posted by maverick808

Did you actually run the application? Do you see the SyncAlive icon in the system tray?

Dear maverick808,

yes I see it, it's blue. I also tried "autostart" and rebooted the system.

Currently I tried to enable developer mode as you describe in the other posting but it looks like the PHM registry editor does not allow me to browse through the registry.

BTW, I am using a Yukon based PPC running Windows Mobile 5.0, OS 5.1.40 (build 14406.1.1.1). It runs well when using Boot Camp on the same system in ActiveSync mode.

Jun 16, 2006, 04:19 PM

maverick808
Senior Member

Join: Apr 2006
Posts: 169

Quote:

Originally Posted by PetraHonig

Perhaps there is a problem with your device entering serial mode. We'll have to try a few things so I'll PM you my email and we can try to sort it out.

__________________
WiFiFoFum Pocket PC Wardriving
www.aspecto-software.com

Jun 17, 2006, 09:35 AM #9
Robster Senior Member Join: Jun 2006 Posts: 209	Hi Installed your program and this is the first time I have actually managed to get Parallels to recognise my WM5 Wizard. It paired them fine but when it starts an Activesyn it suddenly stops. It comes up with the following message:- Activesync encountered a problem on the desktop. Support Code 85010014. Any ideas what this could be? I am running with latest version of the i-mate K-JAM rom. Windows XP Pro with all service packs and updates applied. Activesync 4.1. Any and all help would be very much appreciated. Robin PS My K-JAM is still connected and I can browse it??????

Jun 17, 2006, 09:35 AM

Robster
Senior Member

Join: Jun 2006
Posts: 209

Hi

Installed your program and this is the first time I have actually managed to get Parallels to recognise my WM5 Wizard.

It paired them fine but when it starts an Activesyn it suddenly stops.

It comes up with the following message:-

Activesync encountered a problem on the desktop.

Support Code 85010014.

Any ideas what this could be?

I am running with latest version of the i-mate K-JAM rom.

Windows XP Pro with all service packs and updates applied.

Activesync 4.1.

Any and all help would be very much appreciated.

Robin

PS My K-JAM is still connected and I can browse it??????

Jun 17, 2006, 10:07 AM #10
coopermj@muohio.edu Junior Member Join: Jun 2006 Posts: 14	Not pairing Thanks for sharing the app! But, I'm not having success. :/ I have a Treo 700w that goes through Connecting... but doesn't form a partnership. I even hard reset the 700w since I had originally paired it with my office desktop, but it still just says Connecting... for a while with the spinner spinning and the device shows connected. Then it stops and says No partnerships. I have gone into connection settings and hit the Connect button to restart the wizard and the wizard disappears when I attach, but doesn't start the pairing. Help? Thanks -Micah

Jun 17, 2006, 10:07 AM

#10

coopermj@muohio.edu
Junior Member

Join: Jun 2006
Posts: 14

Not pairing

Thanks for sharing the app! But, I'm not having success. :/

I have a Treo 700w that goes through Connecting... but doesn't form a partnership. I even hard reset the 700w since I had originally paired it with my office desktop, but it still just says Connecting... for a while with the spinner spinning and the device shows connected. Then it stops and says No partnerships.

I have gone into connection settings and hit the Connect button to restart the wizard and the wizard disappears when I attach, but doesn't start the pairing.

Help?

Thanks
-Micah

Jun 17, 2006, 12:09 PM

#11

maverick808
Senior Member

Join: Apr 2006
Posts: 169

Quote:

Originally Posted by Robster

It comes up with the following message:-

Activesync encountered a problem on the desktop.

Support Code 85010014.

I think this might be a problem particular to your setup as I found it mentioned before in this thread...

http://forums.pocketpcfaq.com/viewtopic.php?t=16283.

Maybe try following that thread and deleting your partnerships in activesync?

If that doesn't work completely uninstall and reinstall activesync.

__________________
WiFiFoFum Pocket PC Wardriving
www.aspecto-software.com

Jun 17, 2006, 12:18 PM

#12

maverick808
Senior Member

Join: Apr 2006
Posts: 169

Quote:

Originally Posted by coopermj@muohio.edu

I notice rbushway at the top of the thread has a Treo 700w working. Maybe he could say if he had to do something extra to get it working?

__________________
WiFiFoFum Pocket PC Wardriving
www.aspecto-software.com

Jun 17, 2006, 12:57 PM

#13

Robster
Senior Member

Join: Jun 2006
Posts: 209

Quote:

Originally Posted by maverick808

Hi

Thanks

I tried that between leaving my posting and coming back and it did actually fix it first time around.

However I cannot make it connect a second time. :mad:

Robin

Jun 17, 2006, 01:01 PM

#14

maverick808
Senior Member

Join: Apr 2006
Posts: 169

Quote:

Originally Posted by Robster

Hi

Thanks

I tried that between leaving my posting and coming back and it did actually fix it first time around.

However I cannot make it connect a second time. :mad:

Robin

Could you plug it in and then go into the device manager (control panel->system->hardware) and let me know the category the device is in, it's name and if it has a yellow icon next to it. Thanks.

__________________
WiFiFoFum Pocket PC Wardriving
www.aspecto-software.com

Jun 17, 2006, 03:56 PM #15
msolsona Junior Member Join: Jun 2006 Posts: 15	I had sucess wit 700w in Serial mode. The usbswitch it is already in the Treo. I had aleady upgraded the Treo with MSFP. marc

Jun 17, 2006, 04:17 PM

#16

Robster
Senior Member

Join: Jun 2006
Posts: 209

Quote:

Originally Posted by maverick808

Could you plug it in and then go into the device manager (control panel->system->hardware) and let me know the category the device is in, it's name and if it has a yellow icon next to it. Thanks.

I will if you want but I forced a rest of my K-JAM and it has worked perfectly ever since.

I have connected-disconnected-reconnected at least half a dozen times now and all workiing fine.

My only problem is one you cannot help me with.

I have Sprite Backup and would like to backup my K-JAM to my VM but Sprite causes the K-JAM to reboot as part of the backup procedure and of course I cannot set it to serial.

So for now I cannot backup.

Lets hope Parallels fix this soon but in the meantime your little application is life saver.

THANK YOU.

Robin

Jun 17, 2006, 04:26 PM

#17

maverick808
Senior Member

Join: Apr 2006
Posts: 169

Quote:

Originally Posted by Robster

I will if you want but I forced a rest of my K-JAM and it has worked perfectly ever since.

I have connected-disconnected-reconnected at least half a dozen times now and all workiing fine.

Nope, no need to reset. If it's working just enjoy it. Glad we could help.

__________________
WiFiFoFum Pocket PC Wardriving
www.aspecto-software.com

Jun 17, 2006, 11:45 PM #18
indiekiduk Junior Member Join: Jun 2006 Posts: 10	Amazing What does the usb/serial switcher actually do? Does it just modify the registry?

Jun 18, 2006, 07:39 AM #19
smaug Junior Member Join: Apr 2006 Posts: 8	Motorola Q I'm trying this solution wih the Motorola Q and can't get it to work. Two things happen: 1. I activate the serial mode with the program on the Q and parallels identifies it as a WM5 Device instead of a WM5 NIS Device, so I assume the serial program is working. 2. When I choose the WM5 Device, Parallels gives me an error dialog that the device is already in use and to wait a few minutes and try again; waiting few minutes does no good - I always get the same error 3. The Q freezes and has to be reset by removing the battery. Has anyone got this to work with the Q or any smartphone with WM5? :confused:

Jun 18, 2006, 07:39 AM

#19

smaug
Junior Member

Join: Apr 2006
Posts: 8

Motorola Q

I'm trying this solution wih the Motorola Q and can't get it to work. Two things happen:

1. I activate the serial mode with the program on the Q and parallels identifies it as a WM5 Device instead of a WM5 NIS Device, so I assume the serial program is working.

2. When I choose the WM5 Device, Parallels gives me an error dialog that the device is already in use and to wait a few minutes and try again; waiting few minutes does no good - I always get the same error

3. The Q freezes and has to be reset by removing the battery.

Has anyone got this to work with the Q or any smartphone with WM5? :confused:

Jun 19, 2006, 09:52 AM

#20

rbushway
Junior Member

Join: May 2006
Posts: 8

Quote:

Originally Posted by maverick808

I notice rbushway at the top of the thread has a Treo 700w working. Maybe he could say if he had to do something extra to get it working?

You have to launch the USB Switcher and set it to Serial - you'll need to relaunch USB Switcher everytime you reset your 700W as well.

On the USB select icon on Parallels, make sure that you select Treo 700W as the usb device to use. I hae auto connect set to off.

« Previous Thread | Next Thread »

1 | 2 | 3 | 4 | >

Search this thread	Forum jump
Advanced Search

Thread tools	Display modes
Printable Version Email this Page	Linear Mode Hybrid Mode Threaded Mode

Parallels Technology Network

WM5 for all