Has anybody else tried parallels with host suse 10.2 I have tried on two computers and there is no usb tab in the configuration editor. Also there is no way to add a usb tab into the editor. You can add extra hard drives and so on but no usb. This use to work with SUse 10.1 so i am wondering if this is Suse 10.2. The /etc/fstab is different in suse 10.2 .. IT is given below /dev/hda2 / ext3 acl,user_xattr 1 1 /dev/hda3 /home ext3 acl,user_xattr 1 2 /dev/hda1 swap swap defaults 0 0 proc /proc proc defaults 0 0 sysfs /sys sysfs noauto 0 0 debugfs /sys/kernel/debug debugfs noauto 0 0 usbfs /proc/bus/usb usbfs noauto 0 0 devpts /dev/pts devpts mode=0620,gid=5 0 0 /etc/fstab lines 1-8/8 (END) Can anyone help Paul
I had the same issue with SLED 10 which is essentially SUSE 10.1. SUSE has changed the way it does USB with udev. The answer as I recall is to change the usbfs line to auto not noauto. Then the usbfs looks right to Parallels. Hope this helps
Thanks for your reply Unfortunately this did not fix the problem. There is still no option to add a usb interface. any other help would be appreciated.
I tried on 2 differant machines and I couldn't get Parallels to even config. Both on Suse 10.2. The error says something about not liking the kernel. Ron
I did not have that problem parallels installed just fine on two of my machines. Maybe you do not have the kernel sources installed.
Well, I forgot to install kernel-source. So I did and this is the error I got runnunf paralleles-config: Suse 10.2 machine. Can you help me? Thanks, Ron cd drivers && make clean && cd ../ make[1]: Entering directory `/usr/lib/parallels/drivers' cd drv_main/ && make clean && cd .. make[2]: Entering directory `/usr/lib/parallels/drivers/drv_main' rm -rf *.o *.ko .*.cmd *.mod.c .tmp_versions cd common; rm -rf *.o .*.cmd .tmp_versions; cd .. cd mm; rm -rf *.o .*.cmd .tmp_versions; cd .. make[2]: Leaving directory `/usr/lib/parallels/drivers/drv_main' cd hypervisor/ && make clean && cd .. make[2]: Entering directory `/usr/lib/parallels/drivers/hypervisor' make[2]: Leaving directory `/usr/lib/parallels/drivers/hypervisor' cd drv_net/linux/ && make clean && cd .. make[2]: Entering directory `/usr/lib/parallels/drivers/drv_net/linux' rm -rf *.o *.ko .*.cmd *.mod.c .tmp_versions make[2]: Leaving directory `/usr/lib/parallels/drivers/drv_net/linux' cd drv_virtualnic/ && make clean && cd .. make[2]: Entering directory `/usr/lib/parallels/drivers/drv_virtualnic' rm -rf *.o *.ko .*.cmd *.mod.c .tmp_versions make[2]: Leaving directory `/usr/lib/parallels/drivers/drv_virtualnic' make[1]: Leaving directory `/usr/lib/parallels/drivers' cd drivers && make all && cd ../ make[1]: Entering directory `/usr/lib/parallels/drivers' cd drv_main/ && make clean && cd .. make[2]: Entering directory `/usr/lib/parallels/drivers/drv_main' rm -rf *.o *.ko .*.cmd *.mod.c .tmp_versions cd common; rm -rf *.o .*.cmd .tmp_versions; cd .. cd mm; rm -rf *.o .*.cmd .tmp_versions; cd .. make[2]: Leaving directory `/usr/lib/parallels/drivers/drv_main' cd hypervisor/ && make clean && cd .. make[2]: Entering directory `/usr/lib/parallels/drivers/hypervisor' make[2]: Leaving directory `/usr/lib/parallels/drivers/hypervisor' cd drv_net/linux/ && make clean && cd .. make[2]: Entering directory `/usr/lib/parallels/drivers/drv_net/linux' rm -rf *.o *.ko .*.cmd *.mod.c .tmp_versions make[2]: Leaving directory `/usr/lib/parallels/drivers/drv_net/linux' cd drv_virtualnic/ && make clean && cd .. make[2]: Entering directory `/usr/lib/parallels/drivers/drv_virtualnic' rm -rf *.o *.ko .*.cmd *.mod.c .tmp_versions make[2]: Leaving directory `/usr/lib/parallels/drivers/drv_virtualnic' cd drv_main/ && make && cd .. make[2]: Entering directory `/usr/lib/parallels/drivers/drv_main' make -C /lib/modules/2.6.18.2-34-default/build SUBDIRS=/usr/lib/parallels/drivers/drv_main SRCROOT=/usr/lib/parallels/drivers/drv_main modules make[3]: Entering directory `/usr/src/linux-2.6.18.2-34-obj/i386/default' make[3]: *** No rule to make target `modules'. Stop. make[3]: Leaving directory `/usr/src/linux-2.6.18.2-34-obj/i386/default' make[2]: *** [all] Error 2 make[2]: Leaving directory `/usr/lib/parallels/drivers/drv_main' make[1]: *** [vmmain] Error 2 make[1]: Leaving directory `/usr/lib/parallels/drivers' make: *** [build] Error 2
Yes but I don't know how simple it could be. Install Suse 10.2 with kernel sources and run: parallels-config. That is it. Done it twice. It doesn't need anything more than that. If it is still not working maybe your hardware is not supported. Paul
I'm using a hybrid of SLED 10 and SUSE 10.1 as host and USB works well. In fact it works better on Parallels than VMware. I can use USB scanners, printers and flash sticks with no trouble. This has been using WinXP and a number of Linux flavours as guest. Nothing worked until I changed the default "/etc/fstab" file to load the USBFS. Good luck.
You also need to make sure that the kernel supports usbfs. ____SNIP______ I found that you need to make sure that the kernel is compiled to support usbfs (which I know SUSE 10.2 is NOT (I'm not sure about other distributions)). You can check to see if usbfs is supported by your kernel by checking if there is a usb directory in /proc/bus. If it is not present you can compile the kernel with CONFIG_USB_DEVICEFS enabled (there are decent instructions to recompile on SUSE at http://www.howtoforge.com/kernel_compilation_suse). Once the kernel is installed and the machine rebooted you can check /proc/bus for a usb directory. Good luck.
I have tried many linux os as host and none would allow the usb devices to work. Today i installed the new mepis 6.5 and installed parallels. With windows xp as guest my usb devices are now available! don
