Parallels does not recognize my mac airport

E

ErinM

Bit poster
Parallels only recognizes the internet with the ethernet cable plugged in. I have tried using the run command on the mac side suggested in other threads and my MacBook says the command is not recognized. When I look at my control panel (I am running Windows7) my parallel computer only recognizes a broadband PPPoE network. How can I get Parallels to recognize my Mac airport?

Cheers,

e.
 
using parallels desktop 5 won't recognize airport extreme using Windows 7

I am having the same issue...have tried suggestions on various forums but so far nothing has worked- uninstall reinstall parallels tools, run sudokill (cannot remember exact cmd right now). I was operating through bootcamp previously using windows XP and connecting to the internet without a problem.

As suggested on another parallels forum (written in 2007) I ran ipconfig on the mac side and then config /all on the windows side and here are the results...
Ifconfig from Mac
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x1
inet 127.0.0.1 netmask 0xff000000
gif0: flags=8010<POINTOPOINT,MULTICAST> mtu 1280
stf0: flags=0<> mtu 1280
en0: flags=8963<UP,BROADCAST,SMART,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500
ether 34:15:9e:08:be:a6
media: autoselect
status: inactive
en1: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
ether 34:15:9e:98:06:05
inet6 fe80::3615:9eff:fe98:605%en1 prefixlen 64 scopeid 0x5
inet 10.0.1.7 netmask 0xffffff00 broadcast 10.0.1.255
media: <unknown subtype>
status: active
vnic0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
ether 00:1c:42:00:00:08
inet 10.211.55.2 netmask 0xffffff00 broadcast 10.211.55.255
media: autoselect
status: active
vnic1: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
ether 00:1c:42:00:00:09
inet6 fe80::21c:42ff:fe00:9%vnic1 prefixlen 64 scopeid 0x7
inet 10.37.129.2 netmask 0xffffff00 broadcast 10.37.129.255
media: autoselect
status: active

ipconfig /all from windows
Microsoft Windows [Version 6.1.7600]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.

C:\Users\nicole>ipconfig /all

Windows IP Configuration

Host Name . . . . . . . . . . . . : nicole-PC
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No

Ethernet adapter Local Area Connection:

Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Parallels Ethernet Adapter
Physical Address. . . . . . . . . : 00-1C-42-4B-DA-27
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes

Tunnel adapter isatap.{0F072A85-085E-43C0-9903-95B0C189ED80}:

Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft ISATAP Adapter
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes

Tunnel adapter Teredo Tunneling Pseudo-Interface:

Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Teredo Tunneling Pseudo-Interface
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes

Any suggestions are much appreciated!!
 
using parallels desktop 5 won't recognize airport extreme using Windows 7

I am still not able to connect to the internet through windows 7...
I found the post that suggested this cmd--please on Mac side browse to 'Applications' -> 'Utilities' and open 'Terminal'. Run the following command there:sudo killall -hup pvsnatd--which I tried but was not successful.
If anyone can assist with additional suggestions it is appreciated.
 
You must log in or register to reply here.
Back
Top