Mac Host
Windows XP parallels
I have been able to get to the internet in the past.
I am connected to a router using dhcp. My IP address of my Mac is below.
I am able to get an IP address from windows after a time and it is below. No data is being transferred to the net. I am currently using "default adapter". I the same behavior when I use eth0(I am not currently using wireless). When I use Shared, I don't get an IP, but I have gotten on the internet with shared.
So I get an IP address, but I can't ping anything and no data is being transferred. Here is my ipconfig
Ethernet adapter Local Area Connection 2:
Connection-specific DNS Suffix . :
Autoconfiguration IP Address. . . : 169.254.18.31
Subnet Mask . . . . . . . . . . . : 255.255.0.0
Default Gateway . . . . . . . . . : 169.254.18.31
Here is my ifconfig -a from my mac.
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x1
inet 127.0.0.1 netmask 0xff000000
inet6 ::1 prefixlen 128
gif0: flags=8010<POINTOPOINT,MULTICAST> mtu 1280
stf0: flags=0<> mtu 1280
en0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
inet6 fe80::21b:63ff:fea1:2b3e%en0 prefixlen 64 scopeid 0x4
inet 192.168.0.102 netmask 0xffffff00 broadcast 192.168.0.255
ether 00:1b:63:a1:2b:3e
media: autoselect (100baseTX <full-duplex>) status: active
supported media: autoselect 10baseT/UTP <half-duplex> 10baseT/UTP <full-duplex> 10baseT/UTP <full-duplex,hw-loopback> 10baseT/UTP <full-duplex,flow-control> 100baseTX <half-duplex> 100baseTX <full-duplex> 100baseTX <full-duplex,hw-loopback> 100baseTX <full-duplex,flow-control> 1000baseT <full-duplex> 1000baseT <full-duplex,hw-loopback> 1000baseT <full-duplex,flow-control> none
fw0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 4078
inet 169.254.150.192 netmask 0xffff0000 broadcast 169.254.255.255
lladdr 00:1c:b3:ff:fe:a9:23:1a
media: autoselect <full-duplex> status: inactive
supported media: autoselect <full-duplex>
en1: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
ether 00:1c:b3:c0:f5:53
media: autoselect (<unknown type>) status: inactive
supported media: autoselect
vmnet8: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
inet 192.168.104.1 netmask 0xffffff00 broadcast 192.168.104.255
ether 00:50:56:c0:00:08
vmnet1: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
inet 192.168.210.1 netmask 0xffffff00 broadcast 192.168.210.255
ether 00:50:56:c0:00:01
en2: flags=8963<UP,BROADCAST,SMART,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500
inet6 fe80::21c:42ff:fe00:0%en2 prefixlen 64 scopeid 0x9
inet 10.37.129.2 netmask 0xffffff00 broadcast 10.37.129.255
ether 00:1c:42:00:00:00
media: autoselect status: active
supported media: autoselect
en3: flags=8963<UP,BROADCAST,SMART,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500
inet6 fe80::21c:42ff:fe00:1%en3 prefixlen 64 scopeid 0xa
inet 10.211.55.2 netmask 0xffffff00 broadcast 10.211.55.255
ether 00:1c:42:00:00:01
media: autoselect status: active
supported media: autoselect
Windows XP parallels
I have been able to get to the internet in the past.
I am connected to a router using dhcp. My IP address of my Mac is below.
I am able to get an IP address from windows after a time and it is below. No data is being transferred to the net. I am currently using "default adapter". I the same behavior when I use eth0(I am not currently using wireless). When I use Shared, I don't get an IP, but I have gotten on the internet with shared.
So I get an IP address, but I can't ping anything and no data is being transferred. Here is my ipconfig
Ethernet adapter Local Area Connection 2:
Connection-specific DNS Suffix . :
Autoconfiguration IP Address. . . : 169.254.18.31
Subnet Mask . . . . . . . . . . . : 255.255.0.0
Default Gateway . . . . . . . . . : 169.254.18.31
Here is my ifconfig -a from my mac.
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x1
inet 127.0.0.1 netmask 0xff000000
inet6 ::1 prefixlen 128
gif0: flags=8010<POINTOPOINT,MULTICAST> mtu 1280
stf0: flags=0<> mtu 1280
en0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
inet6 fe80::21b:63ff:fea1:2b3e%en0 prefixlen 64 scopeid 0x4
inet 192.168.0.102 netmask 0xffffff00 broadcast 192.168.0.255
ether 00:1b:63:a1:2b:3e
media: autoselect (100baseTX <full-duplex>) status: active
supported media: autoselect 10baseT/UTP <half-duplex> 10baseT/UTP <full-duplex> 10baseT/UTP <full-duplex,hw-loopback> 10baseT/UTP <full-duplex,flow-control> 100baseTX <half-duplex> 100baseTX <full-duplex> 100baseTX <full-duplex,hw-loopback> 100baseTX <full-duplex,flow-control> 1000baseT <full-duplex> 1000baseT <full-duplex,hw-loopback> 1000baseT <full-duplex,flow-control> none
fw0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 4078
inet 169.254.150.192 netmask 0xffff0000 broadcast 169.254.255.255
lladdr 00:1c:b3:ff:fe:a9:23:1a
media: autoselect <full-duplex> status: inactive
supported media: autoselect <full-duplex>
en1: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
ether 00:1c:b3:c0:f5:53
media: autoselect (<unknown type>) status: inactive
supported media: autoselect
vmnet8: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
inet 192.168.104.1 netmask 0xffffff00 broadcast 192.168.104.255
ether 00:50:56:c0:00:08
vmnet1: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
inet 192.168.210.1 netmask 0xffffff00 broadcast 192.168.210.255
ether 00:50:56:c0:00:01
en2: flags=8963<UP,BROADCAST,SMART,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500
inet6 fe80::21c:42ff:fe00:0%en2 prefixlen 64 scopeid 0x9
inet 10.37.129.2 netmask 0xffffff00 broadcast 10.37.129.255
ether 00:1c:42:00:00:00
media: autoselect status: active
supported media: autoselect
en3: flags=8963<UP,BROADCAST,SMART,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500
inet6 fe80::21c:42ff:fe00:1%en3 prefixlen 64 scopeid 0xa
inet 10.211.55.2 netmask 0xffffff00 broadcast 10.211.55.255
ether 00:1c:42:00:00:01
media: autoselect status: active
supported media: autoselect