In PD 17(M1) The host cannot access the Internet through the virtual machine

Discussion in 'Installation and Configuration' started by StrifeS, Feb 26, 2022.

  1. StrifeS

    StrifeS Bit Poster

    Messages:
    2
    我的操作步骤:
    1、Windows增加host- only网卡
    2、Windows共享VPN到host- only网卡
    3.设置主机的默认路由到虚拟机host-only网卡ip
    这不适用于 M1 PD 17,但适用于英特尔
     
  2. StrifeS

    StrifeS Bit Poster

    Messages:
    2
    My operation steps:
    1. Windows adds host-only network interface card
    2. Windows shares the VPN to the host-only network interface card
    3. Set the default route of the host to the virtual machine host-only network interface card ip
    This doesn't work on the M1 PD 17, But works on Intel
     
  3. DebasmitaM@Parallels

    DebasmitaM@Parallels Staff Member

    Messages:
    1,148
    Hello, we are checking on your issue internally, will get back to you at the earliest.
     
  4. DebasmitaM@Parallels

    DebasmitaM@Parallels Staff Member

    Messages:
    1,148
    Hello, kindly collect the technical report by following this KB article from your Intel Mac and M1 Mac and type the 9 digit technical report ids over here. Kindly reproduce the issue on both of your Mac so we can investigate further. Kindly provide us with detailed steps you have followed for reproducing the issue as well.
     
  5. BallO

    BallO Bit Poster

    Messages:
    95
    I have the same issue, I think. There is no host network interface for the host-only network. I think this has more to do with the MacOS version than the platform.
     
  6. BallO

    BallO Bit Poster

    Messages:
    95
    It should be possible to route the traffic without using the GUI, but for some reason the route command lines don't work in Monterey. Interestingly, I can set the default gateway on a Windows 11 VM on the same host-only network and it connects to the Linux router just fine, so I know the router works. The problem is purely with Monterey not wanting to use my routing table settings. I have no idea what's wrong. I've tried the following:

    > route delete default
    > route add default 10.37.129.3
    > route add default 10.37.129.3 -ifscope bridge101

    netstat -nr seems to show the right routing info but Monterey refuses to use the specified gateway!

    > netstat -nr
    Routing tables

    Internet:
    Destination Gateway Flags Netif Expire
    default 192.168.2.1 UGScg en0
    127 127.0.0.1 UCS lo0
    127.0.0.1 127.0.0.1 UH lo0
    169.254 link#11 UCS en0 !
    192.168.2 link#11 UCS en0 !
    192.168.2.1/32 link#11 UCS en0 !
    192.168.2.1 2:23:df:f9:3f:64 UHLWIir en0 1183
    192.168.2.4/32 link#11 UCS en0 !
    192.168.2.4 b0:be:83:5d:3f:f3 UHLWIi lo0
    224.0.0/4 link#11 UmCS en0 !
    224.0.0.251 1:0:5e:0:0:fb UHmLWI en0
    239.255.255.250 1:0:5e:7f:ff:fa UHmLWI en0
    255.255.255.255/32 link#11 UCS en0 !
     

Share This Page